This machine is a full-automatic hanger forming machine, which can produce all kinds of bare body thread twisting, covered wire twisting and automatic welding to form different shapes and sizes of large and small hanger hooks. Adjust arbitrarily, the output is 25-30 pieces per minute, and the diameter of iron wire is 1.6-4.0mm.
Among them, galvanized wire hangers, hanger sizes: 13 inches, 14 inches, 15 inches, 16 inches, 18 inches (including 16 inches-18 inches skirt hangers). The voltage is 380V motor 1.5-2.2kw, the net weight of the machine is 850kg, pay-off rack and collection hanger rack.
Hanger making machine operating instructions:
First, the switch has manual and automatic, when the switch is set to "manual", the operation mode is control jog. Automatically divided into three operation modes (red, green, black). Among them, the black button is used for the starting point action, the green button is normally started, and the red button is stopped.
Second, loosen the straightening alloy screw and the straightening wheel handle, feed the wire between the wire feeding drive wheel and the wire feeding pinch, adjust the wire feeding pinch handle, and the wire feeding length and short are adjusted by the wire feeding fan gear, Press the jog switch to introduce the wire into the forming mold, and use the jog operation to complete the first hanger, which can be started normally.
3. When the machine is running, it is strictly forbidden to open the safety protection plate.
Routine maintenance of clothes rack making machine:
One: Please cut off the power when the machine is not working, and it is forbidden to use it for a long time.
Two: Every 4 hours of operation, the machine must be shut down and oil is added once in each oil eye to continue the production.
3: Regularly (2 months) check the amount of oil in the gearbox. When the amount of oil is not enough, please add enough or replace the gear oil.
Four: After the machine is stopped, it must be kept clean, dry and ventilated.
Five: Regularly refuel the transmission mechanism to ensure that the machine extends its service life.
Six: The operator of the aircraft must pass the training to get on the job, otherwise it is not allowed to operate.
Hanger making machine composition:
One: (mechanical) control box is provided with jog forward and fast forward.
Two: This machine's wire feeding wheel, straightening wheel, twisting (welding) forming mold are made of high-quality alloy steel, and through vacuum heat treatment, it has high wear resistance and long service life. All shafts are made of 40CR or 45 # steel. After quenching and tempering, its comprehensive mechanical properties are high, and the gears are all made of forged billet. After quenching and tempering and high frequency hardening of the tooth surface, the hardness is precision manufactured up to HRC55-58 degrees.
In short: the machine is focused on maintenance, people are the first, and quality is the first.
Among them, galvanized wire hangers, hanger sizes: 13 inches, 14 inches, 15 inches, 16 inches, 18 inches (including 16 inches-18 inches skirt hangers). The voltage is 380V motor 1.5-2.2kw, the net weight of the machine is 850kg, pay-off rack and collection hanger rack.
Hanger making machine operating instructions:
First, the switch has manual and automatic, when the switch is set to "manual", the operation mode is control jog. Automatically divided into three operation modes (red, green, black). Among them, the black button is used for the starting point action, the green button is normally started, and the red button is stopped.
Second, loosen the straightening alloy screw and the straightening wheel handle, feed the wire between the wire feeding drive wheel and the wire feeding pinch, adjust the wire feeding pinch handle, and the wire feeding length and short are adjusted by the wire feeding fan gear, Press the jog switch to introduce the wire into the forming mold, and use the jog operation to complete the first hanger, which can be started normally.
3. When the machine is running, it is strictly forbidden to open the safety protection plate.
Routine maintenance of clothes rack making machine:
One: Please cut off the power when the machine is not working, and it is forbidden to use it for a long time.
Two: Every 4 hours of operation, the machine must be shut down and oil is added once in each oil eye to continue the production.
3: Regularly (2 months) check the amount of oil in the gearbox. When the amount of oil is not enough, please add enough or replace the gear oil.
Four: After the machine is stopped, it must be kept clean, dry and ventilated.
Five: Regularly refuel the transmission mechanism to ensure that the machine extends its service life.
Six: The operator of the aircraft must pass the training to get on the job, otherwise it is not allowed to operate.
Hanger making machine composition:
One: (mechanical) control box is provided with jog forward and fast forward.
Two: This machine's wire feeding wheel, straightening wheel, twisting (welding) forming mold are made of high-quality alloy steel, and through vacuum heat treatment, it has high wear resistance and long service life. All shafts are made of 40CR or 45 # steel. After quenching and tempering, its comprehensive mechanical properties are high, and the gears are all made of forged billet. After quenching and tempering and high frequency hardening of the tooth surface, the hardness is precision manufactured up to HRC55-58 degrees.
In short: the machine is focused on maintenance, people are the first, and quality is the first.
Comments
Post a Comment